Products

These semi-permanent close-couplings fit in the NEM pockets on Peco 009 rolling stock. They can replace the conventional 009 hoop-and-loop coupling...

Information from Peco's website: The four coaches in this group of vehicles were known as the 'Bowsiders' because of the shape of their sides, a...

Individulay components for building track. Also used for adding 3rd and 4th Conductor rails to existing track as found on Southern, Merseyside and ...

1 set of Frog and Wing Rails for the construction of turnouts, using Code 124 Bullhead rail.

1 set of Turnout Blades and Brackets for the construction of turnouts, using Code 124 Bullhead rail.

Often seen in the loco yard or near the platform end. Use LK-2 Water Cranes if additional cranes are required. Length: 88mm

Can be used with Wills SS83 Stone Piers to create an impressive viaduct as seen on many railways around the world. Detailed plastic moulding suppli...

Can be used with Wills SS83 Stone Piers to create an impressive viaduct as seen on many railways around the world. Detailed plastic moulding suppli...

The pre coloured parts of this plastic kit can be assembled in a number of ways; further kits can be combined to make a larger structure if require...

Laser cut wooden kit with plastic chimney pot detail and glazing sheet. A craft knife, needle files, glue (impact adhesive or PVA work well. Sup...

Laser cut wooden kit with plastic chimney pot detail and glazing sheet. A craft knife, needle files, glue (impact adhesive or PVA work well. Sup...

Laser cut wooden kit with plastic chimney pot detail and glazing sheet. A craft knife, needle files, glue (impact adhesive or PVA work well. Sup...

A craft knife, files and liquid poly cement are required to for assembly Use with LK-12103 Brick platform edges and LK-12107 Brick paviours or L...

A craft knife, files and liquid poly cement are required to for assembly Use with LK-12106 Stone ramps and LK-12107 Brick paviours or LK-12108 c...

A craft knife, files and liquid poly cement are required to for assembly Use with LK-12103 Brick platform edges and LK-12107 Brick paviours or L...

A craft knife, files and liquid poly cement are required to for assembly Use with LK-12103 and LK-12104 platform edging and LK-12105 and LK-1210...

A craft knife, files and liquid poly cement are required to for assembly Use with LK-12103 and LK-12104 platform edging and LK-12105 and LK-1210...

This kit will make 2 Station houses; assembly can be varied , extra doors and windows are included. Length: 73mm Width: 63.5mm

Kit contains detailed plastic parts, rail and electrical contacts, plus full instructions. It may be assembled as a traditional open well type or w...

Usually supplied by a water tower (See LK-1, Ratio 506, 540, 551 and Wills SS34 kits). Length: 68mm

A accurately laser cut wood kit supplemented by injection moulded roof, windows and doors. Glue and paints required to complete model. Lengt...

A accurately laser cut wood kit supplemented by injection moulded roof. Glue and paints required to complete model. Length: 90mm Width:...

Monkton Combe, once an intermediate station on the long-closed Camerton branch near Bath, was thrust into the limelight in 1952 when it was chosen ...

A kit of pre coloured and clear parts that can be built in a number of different ways and can be stood on a platform or on ground level. Len...

Pack of 6 confectionery dispensers.

Pack of 4, 2 different types.

24 Churns, once a common site on station platforms.

6 assorted cases.

Pack of 12 seats, see Modelscene 5056 Seated Passengers Set.

Pack of 12 seats, see Modelscene 5056 Seated Passengers Set.

Kit of a useful general purpose type crane, also often seen at canal basins etc. Length: 146.5mm Depth: 50.8mm

A ubiquitous structure found on every railway. Length: 40mm